DANTE VIRTUAL SOUNDCARD VLAN PATCH

Close flash message: Midi Learn Wavetool Chat to close the flash message by external midi command.

Chat Macros: Edit the messages for the Macros 1-7 and assign a MIDI message as a trigger.

/wtchatflash/QLab/Foh вЂњSHOW IS ABOUT TO BEGIN!вЂќ.

As an example, in QLab it`s possible to do a network cue, which sends a message to Wavetool Chat member(s).

Listen to chat OSC message on port 53005: Chat accepts OSC messages.

Flash screen when chat message is recived: A red frame around the main window will blink on incoming chat message.

Keep chat window always on top: Keeps the chat window on top of all programs.

Macro button scale: Adjust the scale/size of the Macro buttons.

Chat font size: Adjust the size of the font in the chat window.

Chat Username: Set the username you want the Master/Client to show up as, in the chat window.

Under the Preferences / Chat menu you can adjust the following settings. Attention! A10-RACK and EM3532 cannot be used at the same time.

Audio Limited A10 RACK: search A10-RX / Wisycom MCR42 or Lectrosonics SRc devices when WT is launched.

Search for Sennheiser 3532 devices when WT is launched.

Bypass MIDI for snapshots: Bypasses all incoming MIDI commands.

Maintain solo selection after snapshot change.

When not activated, the solo will work in additional solo mode. When activated, you can only listen to a one channel at a time.

Single solo mode is familiar from most of the mixing consoles.

Post gain metering should be used when ever the levels have been trimmed up or down in Wavetool Ch i/o.

Channel metering & SCP mode: Pre Gain / Post Gain setting.

Wavetool Server identifier: In case of multiple Wavetool Master computers in a single network, set an independent identifier name so, that youвЂ™ll know which computer to connect to with iOS/macOS remote.

Audio buffer lenght: Set your desired buffer lenght (shorter = less latency) Attention! 64 samples might not work with all soundcards.

Log warnings to: Choose a place to save your log textfile.

No signal threshold: dBFS from -180 to -60 (0 = off) Set the threshold for when you want to show the No signal Warning.

Battery alert threshold: Set the threshold for when you want to show the Low Battery Warning.

RF alert threshold: Set the threshold for when you want to show the Low RF Warning.

If your artist is running back and forth to a dressing room with no RF coverage then the Low RF alert will be reset once the transmitter is within range. Maybe you are preparing the gig and donвЂ™t want multiple alerts going off. If you are working on a loud stage or microphones are near bass cabinets you will need to lower the sensitivity. SCP looks for very low frequencies that are produced when a cable is broken.

Low frequency detector sensitivity (Default: High).

Turn off SCP per channel in Wavetool Ch i/o. SCP is looking for un-natural sounds and you might need to change this setting depending on type of microphone or sound source. Lower the setting if you are getting too much errors. Under the Preferences / General menu you can adjust the following settings.

Audio memory usage: Shows how much memory is used by Instant Replay.

(read more here about creating separate mixes to connected remotes.) It is also possible to create an Aggregate device in macOS Audio MIDI setup if you want to go crazy and use a lot of inputs. Note that different in/out device combinations are possible.

DANTE VIRTUAL SOUNDCARD VLAN PATCH

Output channels: Patch the stereo output of the application to the correct channel on your audio device.Set Gain On Selected Channels: Lets you gain multiple channels at once.Link group: Link channel solos by choosing a Link group.These channels will be soloed when there`s no active solo selection Enable Instant Replay on selected channel.Choose the panel (A or B) where the channel is shown.Pan: Between -100 (left) and 100 (right).Disable RF Warnings: If your transmitters move out of reach a lot you might not want to be alerted every time.Disable SCP to avoid too many false alerts. Disable SCP: SCP is designed for live microphones.Player: Assign a player to your channel (read more here).

This will display RF and battery data in the main window. Link an RF receiver to the input channel. Wireless device: Click a row to show a list of found receivers.Unpatch selectedвЂ¦: First choose the channels to be unpatched (for example 1-32) and then click Unpatch selectedвЂ¦ tab to set the inputs for the selected channels to be NONE.

Patch selectedвЂ¦: First choose the channels to patch (for example from 1-64) and then input the first channel to be patched.

Input ch: Assign hardware inputs to channels.

Name: Edit names by double clicking on the name.

Dante virtual soundcard vlan